Dynapac CA270 Скачать руководство пользователя страница 79

Страница: 79 / 99

Maintenance - 50h

ICA270-IN2EN1.pdf

2012-11-05

Articulation - Lubrication

Fig. Steering hitch right side

Do not allow anyone to remain in the vicinity of the
steering joint when the engine is running. Risk of
being crushed when the steering is operated.
Press the emergency/parking brake knob before
lubricating.

Turn the steering wheel fully to the left to gain access
to all the steering system's lubricating nipples (4) on
the right-hand side of the machine.

Use grease as per the lubricant specification

Steering joint - Lubrication

Fig. Articulation, right side
1. Lubricating nipples, articulation
(4 pcs)

Wipe off any dirt and grease from the nipples.

Grease each nipple (1) with five strokes of a
hand-operated grease gun. Make sure that grease
penetrates into the bearings.

If grease does not penetrate the bearings, it may
be necessary to relieve the articulation joint with a
jack while repeating the greasing process.

Содержание CA270




































































































Результаты поиска

Содержание CA270

Отзывы:

Похожие инструкции для CA270

Бренды по названию

Популярные бренды

Dynapac CA270, Инструкция по эксплуатации

Результаты поиска

Содержание CA270

Отзывы:

Похожие инструкции для CA270

Бренды по названию

Популярные бренды