background image

Maintenance - 50h

ICA270-IN2EN1.pdf

2012-11-05

Maintenance - 50h

Park the roller on a level surface.
When checking and making adjustments, the
engine should be switched off and the
emergency/parking brake should be applied, if
not otherwise specified.

Park the roller on a level surface.
When checking and making adjustments, the
engine should be switched off and the
emergency/parking brake should be applied, if
not otherwise specified.

Ensue that there is good ventilation (air
extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.

Ensue that there is good ventilation (air
extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.

Air cleaner
Checking - Change the main air filter

Change the air cleaner main filter when the
warning lamp on the control panel comes on
when the engine is running at maximum speed.

Change the air cleaner main filter when the
warning lamp on the control panel comes on
when the engine is running at maximum speed.

3

6

4

5

2

Fig.  Air cleaner
 1. Clips
 2. Cover
 3. Main filter
 4. Backup filter
 5. Filter housing
 6. Dust valve

1

Release the clips (1), pull off the cover (2), and pull out
the main filter (3).

Do not remove the backup filter (4).

Clean the air cleaner if necessary, see section Air
cleaner - Cleaning.

When replacing the main filter (3), insert a new filter
and refit the air cleaner in the reverse order.

Check the condition of the dust valve (6); replace if
necessary.

When refitting the cover, make sure that the dust valve
is positioned downwards.

69

Содержание CA270




































































































Отзывы: