Dynapac CA270 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 99

background image

Operation

ICA270-IN2EN1.pdf

2012-11-05

Operating

Operating the roller

Under no circumstances is the machine to be
operated from the ground. The operator must be
seated inside the machine during all operation.

Under no circumstances is the machine to be
operated from the ground. The operator must be
seated inside the machine during all operation.

33

6

3

1

Fig. Control panel
1. Ignition starter switch
3. Emergency shut down
6. Forward/Back regulator
33. Engine speed control

Pull back the engine speed control (33) until it locks in
the operational position.

Check that the steering is working correctly by turning
the steering wheel once to the right and once to the
left while the roller is stationary.

Make sure that the area in front of and behind the
roller is clear.

Make sure that the area in front of and behind the
roller is clear.

Carefully move the forward/reverse lever (6) forwards
or backwards, depending on which direction of travel
is required.

The speed increases as the lever is moved away from
the neutral position.

The speed should always be controlled by using
the forward/reverse lever, and never by changing
the engine speed.

The speed should always be controlled by using
the forward/reverse lever, and never by changing
the engine speed.

Test the emergency stop by pressing the
emergency stop button (3) while the roller is
moving slowly forward. Brace yourself for a
sudden stop. The engine will be switched off and
the brakes activated.

Test the emergency stop by pressing the
emergency stop button (3) while the roller is
moving slowly forward. Brace yourself for a
sudden stop. The engine will be switched off and
the brakes activated.

Check while driving that the warning lamps have not
gone on.

If the engine is overheated or if the oil pressure is
to low then the buzzer sounds for 10 seconds and
the engine shuts off. Brace your self for a sudden
stop.

If the engine is overheated or if the oil pressure is
to low then the buzzer sounds for 10 seconds and
the engine shuts off. Brace your self for a sudden
stop.

38

«
...
44
45
46
47
48
...
»

Содержание CA270




































































































Отзывы:

Нет отзывов

Похожие инструкции для CA270

Бренд: Navman Страницы: 17

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Mangar International Страницы: 8

Бренд: zarges Страницы: 36

Бренд: VDO Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды