Dynapac CA270 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 99

background image

Preventive maintenance

ICA270-IN2EN1.pdf

2012-11-05

Preventive maintenance

Complete maintenance is necessary for the machine
to function satisfactorily and at the lowest possible
cost.

The Maintenance section includes the periodic
maintenance that must be carried out on the machine.

The recommended maintenance intervals assume that
the machine is used in a normal environment and
working conditions.

Acceptance and delivery inspection

The machine is tested and adjusted before it leaves
the factory.

On arrival, before delivery to the customer, delivery
inspection must be conducted as per the check list in
the warranty document.

Any transport damage must be immediately reported
to the transport company.

Warranty

The warranty is only valid if the stiplulated delivery
inspection and the separate service inspection have
been completed as per the warranty document, and
when the machine has been registered for starting
under the warranty.

The warranty is not valid if damage has been caused
by inadequate service, incorrect use of the machine,
the use of lubricants and hydraulic fluids other than
those specified in the manual, or if any other
adjustments have been made without the requisite
authorisation.

53

«
...
59
60
61
62
63
...
»

Содержание CA270




































































































Отзывы:

Нет отзывов

Похожие инструкции для CA270

Бренд: Laica Страницы: 4

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: TAIKO Audio Страницы: 24

Бренд: Mandam Страницы: 9

Бренд: Jackco Страницы: 6

Бренд: Gamry Instruments Страницы: 69

Бренд: Rayger Страницы: 2

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: YASKAWA Страницы: 1166

Бренд: Hammer Strength Страницы: 8

Бренд: Rigol Страницы: 12

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

Бренд: DALBO Страницы: 27

Infinity Wash XL

Бренд: Coemar Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды