manualshive.com logo in svg

Dynapac CA270, Инструкция по эксплуатации


Поделиться
Скачать
background image

Miscellaneous

ICA270-IN2EN1.pdf

2012-11-05

Fig. Drum motor

Releasing the parking brake in the drum

1

Remove and dispose of the rubber plug from the
brake protector.
Loosen the metallic plug.

1

Remove and dispose of the rubber plug from the
brake protector.
Loosen the metallic plug.

2

Use a screw fitted with a nut and washer.
Tighten to the bottom of the threading into the
piston without blocking the screw.

2

Use a screw fitted with a nut and washer.
Tighten to the bottom of the threading into the
piston without blocking the screw.

3

Then tighten the nut until the motor shaft turns
freely, while holding the screw.

3

Then tighten the nut until the motor shaft turns
freely, while holding the screw.

The brake is now disengaged and the machine can be
towed.

Reset the drum motor brake after towing.

Reset the drum motor brake after towing.

48

Содержание CA270




































































































Отзывы:

Нет отзывов

Похожие инструкции для CA270

Campbell CS500 Instruction Manual preview
CS500
Бренд: Campbell Страницы: 18
Vector 0 Owner'S Manual & Warranty Information preview
0
Бренд: Vector Страницы: 4
Keiser M3 Calibration Procedure preview
M3
Бренд: Keiser Страницы: 2
ECA OASIS Installation Sheet preview
OASIS
Бренд: ECA Страницы: 3
Nautilus ONE Owners Instructions And Assembly preview
ONE
Бренд: Nautilus Страницы: 12
VeEX FX30 Quick Manual preview
FX30
Бренд: VeEX Страницы: 2
JB-Lighting P8 Operating Instructions Manual preview
P8
Бренд: JB-Lighting Страницы: 48
XAG P30 Quick Start Manual preview
P30
Бренд: XAG Страницы: 24
Parker HTG Series Service Procedure preview
HTG Series
Бренд: Parker Страницы: 64
Parker F11 series Service Spare Parts List preview
F11 series
Бренд: Parker Страницы: 40
Parker Matrx Digital MDM Cabinet Mount Installation Instructions preview
Matrx Digital MDM
Бренд: Parker Страницы: 20
XFit TARGET User Manual preview
TARGET
Бренд: XFit Страницы: 16
Nakamichi BlackBox Series Service Manual preview
BlackBox Series
Бренд: Nakamichi Страницы: 23
Harken 3387 Instructions preview
3387
Бренд: Harken Страницы: 4
U-Line H-8379 Manual preview
H-8379
Бренд: U-Line Страницы: 6
WAVEFIT R100 Swell Series Owner'S Manual preview
R100 Swell Series
Бренд: WAVEFIT Страницы: 30
xsto ZW4 D Series Operation Manual preview
ZW4 D Series
Бренд: xsto Страницы: 63
Native Instruments TRAKTOR KONTROL S3 Manual preview
TRAKTOR KONTROL S3
Бренд: Native Instruments Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды