Dynamica HALO RB-10 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 86

Dynamica HALO RB-10 Скачать руководство пользователя страница 26

1-7

The printer connector is on the right side of the instrument as shown in Fig 1-3.
The HALO RB-10 is compatible with many printers, including the Seiko thermal
printer with DPU setting, Hewlett Packard printer with PCL/3 setting and the Epson
Printer with ESC/P setting. For a detailed list of the printers that are compatible
with the HALO RB-10, contact your local Dynamica representative. To define the
printer type connected to the HALO RB-10, please refer to the System setting
section interface under printer setting sub menu.
Please refer to the relevant printer instruction manual to install the printer.

1.8 Local-Remote switch

The HALO RB-10 can be controlled by the optional PC software, or simply via
keypad control. Please put the Local-Remote switch to Local when using the
keypad and LCD on the HALO RB-10. When connecting to PC software, switch
the Local-Remote switch to the Remote position. The LCD will display < PC Control
> when connected to PC software for complete instrumentation control and data
analysis.

1.9 LCD Brightness adjustment port

The LCD brightness can be adjusted through this port by turning the screw using a
small flat blade screwdriver.

1.10 Connecting Accessories to the HALO RB-10

The Acc port is provided for the connection and control of a variety of optional
accessories available from Dynamica, such as a sample autosipper or electronic
thermostatic cell holder. Connect the optional accessories using the cable provided
with the accessories themselves. Please refer to the installation manual for
installation details for the optional accessories.

1.11 Connecting the HALO RB-10 to PC Software

The optional PC software allows the HALO RB-10 to be fully controlled by the
software and perform data analysis. Connect the serial cable provided with PC
software to the port marked PC. Please also set the Local-Remote switch to
Remote when using PC software.

«
...
24
25
26
27
28
...
»

Содержание HALO RB-10























































































Отзывы:

Нет отзывов