Duke RCO Скачать руководство пользователя страница 6

Страница: 6 / 56

Service Manual for

RCO Speed Oven

INSTALLATION

ELECTRICAL REQUIREMENTS

TO AVOID RISK OF ELECTRICAL

SHOCK OR DEATH, THIS OVEN MUST BE

GROUNDED AND ITS PLUG MUST NOT BE

ALTERED.

The operation of this microwave oven can cause

voltage fluctuations on the supply line. The

operation of this oven under unfavorable voltage

supply conditions can have adverse effects.

• This device is intended for the connection to a

power supply system with maximum permissible

system impedance Zmax of 1.1Ω at the interface

point of the user’s supply.

• The user MUST ensure that this device is connected only

to a power supply system which fulfills this requirement.

• The public power supply company can provide

system impedance at the interface point.

• The fuse used in this oven is Ferraz Shawmut

OTM30 Fuse (Duke PN: 168120, 250 VAC, 30 A).

GROUNDING INSTRUCTIONS

IMPROPER INSTALLATION

OR GROUNDING CAN RESULT IN RISK

OF ELECTRICAL SHOCK. CONSULT A

QUALIFIED ELECTRICIAN OR SERVICEMAN

IF THE GROUNDING INSTRUCTIONS ARE NOT

COMPLETELY UNDERSTOOD, OR IF DOUBT

EXISTS AS TO WHETHER THE APPLIANCE

IS PROPERLY GROUNDED. DO NOT USE AN

EXTENSION CORD. IF THE POWER SUPPLY

CORD IS TOO SHORT, HAVE A QUALIFIED

ELECTRICIAN OR SERVICEMAN INSTALL AN

OUTLET NEAR THE APPLIANCE.

Grounding reduces risk of electric shock by providing

a conductor for the electric current if an electrical

short occurs.

• This oven is equipped with a cord and plug

containing a properly wired ground.

UNPACKING

Inspect oven for physical damage to the cabinet. Also

check the oven cavity for damage. Report any damage

to the source of purchase immediately. Do not attempt

to install or use the oven if damaged.

Remove all materials from oven interior.

If oven has been stored in an extremely cold area, wait

a few hours before connecting power.

RADIO INTERFERENCE

Microwave operation may cause interference to radio,

television, or a similar oven. Reduce or eliminate

interference by performing the following:

• Keep the oven door and sealing surfaces of the

oven clean according to instructions in Care and

Cleaning instruction in the OPERATORS MANUAL

(Duke PN:168913).

• Place radio, television, etc. as far as possible from

the oven

• Use a properly installed antenna (radio/TV) will

help to eliminate interference caused by the oven.

OVEN PLACEMENT

•

Do not install the oven next to or above source of

heat, such as pizza oven or deep fat fryer.

•

Install the oven on a level countertop surface.

•

Provide clearance as described in the Specifications

section.

WARNING

RISK OF APPLIANCE FALLING.

RISK OF PERSONAL INJURY

ONLY operate appliance if its legs are in direct

contact with the countertop or supporting

surface. If the legs are not in direct contact with

the supporting surface, the appliance can creep

slowly during repeated use, eventually falling

off the surface when the door is opened. Such

a fall could possibly injure anyone nearby. The

appliance is often installed using sliding pads

which are inserted between its legs and

supporting surface. These sliding pads MUST

be removed before operating the oven. Nothing

else should be inserted between the legs and the

supporting surface.

Содержание RCO

























































Результаты поиска

Содержание RCO

Отзывы:

Похожие инструкции для RCO

Бренды по названию

Популярные бренды

Duke RCO, Руководство по обслуживанию

Результаты поиска

Содержание RCO

Отзывы:

Похожие инструкции для RCO

Бренды по названию

Популярные бренды