Docomo SH-05A, Инструкция по эксплуатации, Страница: 542 / 556

25
Manual for PC Connection_DR20.fm
AT+CGDCONT Sets host (APN) accessed when
establishing packet
transmission.
*2
Refer to “More on AT commands” (
n
P. 31). Refer to “More on
AT commands”
(
n
P. 31).
AT+CGEQMIN Registers criterion determining
whether to permit QoS (Quality of
Service) sent from network when
establishing packet transmission.
*2
Refer to “More on AT commands” (
n
P. 32). Refer to “More on
AT commands”
(
n
P. 32).
AT+CGEQREQ Sets QoS (Quality of Service)
requested of network during
packet transmission.
*2
Refer to “More on AT commands” (
n
P. 33). Refer to “More on
AT commands”
(
n P. 33).
AT+CGMR Displays FOMA terminal
version.
*2
―
AT+CGMR
o
12345678901234
56
OK
AT+CGREG=
<n> Sets whether to send network
registration status. Service area
information (inside/outside) is
sent.
*1
<n>
0:
Does not set (default setting)
1: Sets
When AT+CGREG=1 is set, information
is sent in the format “+CGREG:<stat>”.
0, 1, 4 or 5 can be set for the <stat>
parameter.
<stat>
0:
Outside area
1: Inside area (home)
4: Unknown
5: Inside area (visitor)
AT+CGREG=1
o
OK
(Set to send)
AT+CGREG?
o
+CGREG:1,0
OK
(Indicates outside
area)
+CGREG:1
(Moved from
outside area to
inside area)
AT+CGSN Displays the FOMA terminal’s
serial number.
*2
―
AT+CGSN
o
123456789012345
OK
AT+CLIP=<n> Shows PC calling number when
receiving 64K data
communication.
*1
<n>
0:
Does not output results (default setting)
1: Outputs results
DiCLIP:<n>,<m> for “AT+CLIP?”.
<m>
0:
NW setting to not send own number
during transmissions
1: NW setting to send own number during
transmissions
2: Unknown
AT+CLIP=0
o
OK
AT+CLIP?
o
+CLIP:0,1
OK
AT+CLIR=<n> Sets whether to send terminal’s
phone number when establishing
64K data communication.
*2
<n>
0:
Follows the service agreement
1: Does not send
2: Sends (default setting)
DiCLIR:<n>,<m> for AT+CLIR?.
<m>
0:
CLIR is not running (always send)
1: CLIR is always running (never send)
2: Unknown
3: CLIR temporary mode (default setting is
Do not send)
4: CLIR temporary mode (default setting is
Send)
AT+CLIR=0
o
OK
AT+CLIR? o
+CLIR:2,3
OK
AT+CDIP=<n> Sets whether to send an incoming
sub-address. Also, check the
status of Multi Number
subscription. <n>
0:
Does not display sub-addresses
(default setting)
1: Displays sub-addresses
<m>
0:
Multi Number is not subscribed
1: Subscribing Multi Number
2: Unknown
AT+CDIP=0
o
OK
AT+CDIP?
o
+CDIP:0,1
OK
AT command Overview Parameter/Explanation
Execution
example
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
Manual for PC Connection_DR20.fm 25 ページ ２００９年５月１４日 木曜日 午前１０時５２分