Ditch Witch JT920 Скачать руководство пользователя страница 19

Страница: 19 / 169

JT920/JT920L - CONTROLS

DRILL OVERVIEW

JT920/JT920L - CONTROLS

DRILL OVERVIEW

Throttle Switch

This switch controls remote fluid
unit engine speed.

•

Press top to run engine at
maximum speed.

•

Press bottom to run engine at
idle speed.

This switch only works when fluid
unit throttle switch is in idle
position.

Wrench Control

This lever controls front wrench
(near pipe guide) and back wrench
(at spindle).

Pull or push lever to control back
wrench.

•

Pull to release pipe.

•

Push to lock onto pipe flats.

Move lever to right or left to control
front wrench.

•

Move right to lock onto pipe flats.

•

Move left to release pipe.

ic0050c.eps

ic1057c.eps

Throttle Switch

This switch controls remote fluid
unit engine speed.

•

Press top to run engine at
maximum speed.

•

Press bottom to run engine at
idle speed.

This switch only works when fluid
unit throttle switch is in idle
position.

Wrench Control

This lever controls front wrench
(near pipe guide) and back wrench
(at spindle).

Pull or push lever to control back
wrench.

•

Pull to release pipe.

•

Push to lock onto pipe flats.

Move lever to right or left to control
front wrench.

•

Move right to lock onto pipe flats.

•

Move left to release pipe.

ic0050c.eps

ic1057c.eps

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды