Ditch Witch JT920 Скачать руководство пользователя страница 58

Страница: 58 / 169

JT920/JT920L - PREPARATION

INSPECT SITE

JT920/JT920L - PREPARATION

INSPECT SITE

Select Start and End Points

Select one end to use as a starting point. Consider the following
when selecting a starting point:

Slope

Fluid system should be parked on a level site. Consider how
slope will affect drilling unit setup, bending pipe, and fluid flow out
of hole.

Traffic

Vehicle and pedestrian traffic must be a safe distance from
drilling equipment. Allow at least 10’ (3 m) buffer zone around
equipment.

Space

Check that starting and ending points allow enough space for
gradual pipe bending. See "Minimum Setback" in this chapter.

Check that there is enough space to work and to set up electric
strike system.

Comfort

Consider shade, wind, fumes, and other site features.

Drill downhill when possible so fluid will flow away from drilling
unit.

Select Start and End Points

Select one end to use as a starting point. Consider the following
when selecting a starting point:

Slope

Fluid system should be parked on a level site. Consider how
slope will affect drilling unit setup, bending pipe, and fluid flow out
of hole.

Traffic

Vehicle and pedestrian traffic must be a safe distance from
drilling equipment. Allow at least 10’ (3 m) buffer zone around
equipment.

Space

Check that starting and ending points allow enough space for
gradual pipe bending. See "Minimum Setback" in this chapter.

Check that there is enough space to work and to set up electric
strike system.

Comfort

Consider shade, wind, fumes, and other site features.

Drill downhill when possible so fluid will flow away from drilling
unit.

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды