Ditch Witch JT920 Скачать руководство пользователя страница 27

Страница: 27 / 169

JT920/JT920L - CONTROLS

ANCHORING SYSTEM CONSOLE OVERVIEW

JT920/JT920L - CONTROLS

ANCHORING SYSTEM CONSOLE OVERVIEW

ANCHORING SYSTEM CONSOLE
DESCRIPTIONS

Left Rotation Control

This lever controls rotation of left
anchor.

•

Push to drive anchor.

•

Pull to remove anchor.

Left Thrust Control

This lever controls thrust of left
anchor.

•

Push to move down.

•

Pull to move up.

Right Rotation Control

This lever controls rotation of right
anchor.

•

Push to drive anchor.

•

Pull to remove anchor.

ANCHORING SYSTEM CONSOLE
DESCRIPTIONS

Left Rotation Control

This lever controls rotation of left
anchor.

•

Push to drive anchor.

•

Pull to remove anchor.

Left Thrust Control

This lever controls thrust of left
anchor.

•

Push to move down.

•

Pull to move up.

Right Rotation Control

This lever controls rotation of right
anchor.

•

Push to drive anchor.

•

Pull to remove anchor.

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды