Ditch Witch JT920 Скачать руководство пользователя страница 56

Страница: 56 / 169

JT920/JT920L - PREPARATION

INSPECT SITE

JT920/JT920L - PREPARATION

INSPECT SITE

INSPECT SITE

Inspect jobsite before transporting equipment. Check for the
following:

•

Overall grade or slope

•

Changes in elevation such as hills or open trenches

•

Obstacles such as buildings, railroad crossings, or streams

•

Signs of utilities (See

SAFETY

)

•

Traffic

•

Access

•

Soil type and condition

•

Water supply

•

Sources of locator interference (rebar, railroad tracks, etc.)

Take soil samples from several locations along bore path to
determine best bit and backreamer combinations.

INSPECT SITE

Inspect jobsite before transporting equipment. Check for the
following:

•

Overall grade or slope

•

Changes in elevation such as hills or open trenches

•

Obstacles such as buildings, railroad crossings, or streams

•

Signs of utilities (See

SAFETY

)

•

Traffic

•

Access

•

Soil type and condition

•

Water supply

•

Sources of locator interference (rebar, railroad tracks, etc.)

Take soil samples from several locations along bore path to
determine best bit and backreamer combinations.

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды