Ditch Witch JT920 Скачать руководство пользователя страница 53

Страница: 53 / 169

JT920/JT920L - SAFETY

SAFETY ALERTS

JT920/JT920L - SAFETY

SAFETY ALERTS

Flying objects may cause injury.

Wear hard hat and safety glasses.

Hot parts may cause burns. Do not

touch until cool.

Exposure to high noise levels may

cause hearing loss. Wear hearing protection.

Fall possible. Slips or trips may

result in injury. Keep area clean.

Battery acid may cause burns.

Avoid contact.

Improper handling or use of

chemicals may result in illness, injury, or
equipment damage. Follow instructions on labels
and in material safety data sheets (MSDS).

Flying objects may cause injury.

Wear hard hat and safety glasses.

Hot parts may cause burns. Do not

touch until cool.

Exposure to high noise levels may

cause hearing loss. Wear hearing protection.

Fall possible. Slips or trips may

result in injury. Keep area clean.

Battery acid may cause burns.

Avoid contact.

Improper handling or use of

chemicals may result in illness, injury, or
equipment damage. Follow instructions on labels
and in material safety data sheets (MSDS).

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды