Ditch Witch JT920 Скачать руководство пользователя страница 20

Страница: 20 / 169

JT920/JT920L - CONTROLS

DRILL OVERVIEW

JT920/JT920L - CONTROLS

DRILL OVERVIEW

Remote Throttle Switch

This switch controls engine speed
during drilling and backreaming.

•

Press top to increase speed.

•

Press bottom to decrease
speed.

This switch only works if throttle
switch is in neutral position.

Remote Engine Stop Switch

This button stops drilling unit and
remote fluid unit (if used) engines
from operator station.

•

Press red button on operator’s
station to stop engine(s).

•

Use ignition or remote restart
switch(es) to restart engine(s).

ic0136h.eps

ic1273a.eps

Remote Throttle Switch

This switch controls engine speed
during drilling and backreaming.

•

Press top to increase speed.

•

Press bottom to decrease
speed.

This switch only works if throttle
switch is in neutral position.

Remote Engine Stop Switch

This button stops drilling unit and
remote fluid unit (if used) engines
from operator station.

•

Press red button on operator’s
station to stop engine(s).

•

Use ignition or remote restart
switch(es) to restart engine(s).

ic0136h.eps

ic1273a.eps

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды