Ditch Witch JT920 Скачать руководство пользователя страница 100

Страница: 100 / 169

100

JT920/JT920L - OPERATION

SURFACE DRILL HEAD

100

JT920/JT920L - OPERATION

SURFACE DRILL HEAD

SURFACE DRILL HEAD

Guide drill head to target pit or up through surface. Make all
bends gradual. See "Bend Limits" in

SETUP

Clean area around exit point.

Turn fluid flow control to off position and remote throttle
switch to idle position as soon as drill head emerges.

Clean drill head especially around threads.

Attach quick wrench in break position.

NOTICE:

Never use machine torque to tighten or loosen any

joint. Use quick wrench only.

•

Place jaws (1) on wrench flats on both sides of joint.

•

Pin handles (2) to wrench jaws. Be sure handles are both
up.

•

Attach pivoting nut heads (3) so that screw (4) is over joint.

•

Turn screw to pull handles together.

Loosen joint.

Turn screw opposite way two turns to relieve pressure and
remove quick wrench components.

Remove drill head.

om2053a.eps

SURFACE DRILL HEAD

Guide drill head to target pit or up through surface. Make all
bends gradual. See "Bend Limits" in

SETUP

Clean area around exit point.

Turn fluid flow control to off position and remote throttle
switch to idle position as soon as drill head emerges.

Clean drill head especially around threads.

Attach quick wrench in break position.

NOTICE:

Never use machine torque to tighten or loosen any

joint. Use quick wrench only.

•

Place jaws (1) on wrench flats on both sides of joint.

•

Pin handles (2) to wrench jaws. Be sure handles are both
up.

•

Attach pivoting nut heads (3) so that screw (4) is over joint.

•

Turn screw to pull handles together.

Loosen joint.

Turn screw opposite way two turns to relieve pressure and
remove quick wrench components.

Remove drill head.

om2053a.eps

Содержание JT920










































































































































































Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды

Ditch Witch JT920, Руководство пользователя

Результаты поиска

Содержание JT920

Отзывы:

Похожие инструкции для JT920

Бренды по названию

Популярные бренды