JMB-R
:
REV
0
DiBO
n.v.
58
6. Service
6.1. General
All maintenance activities must happen at an
disconnected machine
and
hoses without pressure
.
Checking the electric components can happen exclusively by an expert.
Exclusively accessories and replacement components which have been approved by the manufacturer can be
used. Directly after the activities all securities- and protection parts must be assembled, before the machine is
put in functioning.“a golden rule” that contributes to a perfectly working machine with few problems, is following:
A DAILY CONTROL AND CLEANING OF THE MACHINE FREQUENTLY DO WONDERS!
7REHDEOHWRJXDUDQWHHDSHUIHFWO\ZRUNLQJV\VWHPRQHKDV¿UVWQHFHVVDU\DUHOLDEOHDQGWHFKQLFDOZHOOFRQVLG
-
ered machine, which is then faced secondly at regular times with a thorough maintenance.
Therefore the experience and the “know-how” of DiBO a technical good working machine is insured and large
maintenance turns can be carried out by experienced DiBO technicians by means of appointment or mainte-
QDQFHFRQWUDFWZHFDQVXSSRVHLQDGYDQFHWKDWLWLVVDWLV¿HGWRWKHVHWZRSRLQWV
6.2. Maintenance diagram
6.2.1 General
Check daily by means of the maintenance diagram the high pressure cleaner.
<RX¿QGWKHPDLQWHQDQFHGLDJUDPRQWKHIROORZLQJSDJHV
Check even all transmission belts on good tension and possible defects.
If this case is not, then best consult the proper maintenance technicians.
PAY ATTENTION: Take care that the transmission belts aren’t in movement and observe the applying safe
standards!
6.2.2. Periodic maintenance
- Control of the electric cables, high and low pres-
sure hoses and couplings and control of oil level.
After each use.
- Refreshing pump oil.
First 50 hours.
&OHDQLQJZDWHU¿OWHU
Each 50 hours.
5HSODFHPHQWDQGFOHDQLQJRLO¿OWHUVDQGIXHO
¿OWHUV
First 50 hours, each following 200 hours.
- Cleaning fuel tank.
First 50 hours, each following 200 hours.
- All following refreshments of pump oil and reduc-
tion gearbox oil.
Each 200 hours.
- Maintenance engine.
See enclosed motor instruction manual.
- Extra control/replacement of joints, valves, o- rings
by acknowledged DiBO- technicians!
Each 600 hours.
6.2.3. Control of oil level and refreshing pump oil
Check for each use of the machine the oil with the oil level glass or with the oil level bar.
Oil must stand right with the sign of the oil level glass, if the this case is not, oil tops up until the sign.
If oil looks forward to there milky, consult directly the DiBO technicians. To refresh oil, as follows work goes:
- Unbolt the drain plug below the pump.
- Unbolt the tap with the oil level bar.
- Catch all oil in a barge and remove oil like further described in the guide.
- Force up the drain plug there and top up the oil in the breach to the upper part to on the mark line.
- Force up the tap with the oil level bar there.
- Recommended oil: 1.836.042.
&OHDQLQJRIWKHZDWHU¿OWHUV
&OHDQWKHZDWHU¿OWHUVUHJXODUDQGUHPRYHSRVVLEOHGLUW
&OHDQLQJRIWKHRLODQGIXHO¿OWHUV
7KHRLODQGIXHO¿OWHUVGHIXVHDQGFOHDQLQJSRVVLEO\UHSODFH(PSW\WKHIXHOWDQN
Remove the drain plug and catch possible dirt in a can.
Rinse clean the tank with a little it off clean fuel and turn close the drain plug.
Содержание JMB-R 100/40 Series
