JMB-R
:
REV
0
DiBO
n.v.
59
6.2.6. Maintenance at expense of technicians
For further maintenance we advise to contact your DiBO distributor concerning a maintenance contract.
The maintenance applies to normal company circumstances.
At heavy circumstances you can communicate this so that can be taken into account.
Supplement documents:
Control manual
&(FHUWL¿FDWH
Electrical plans
Remarks:
It is recommend the preventive maintenance to carry out by a competent DiBO- service technician accord-
ing to this maintenance diagram, to be able to remain use the machine up to maximum and also to be able
to claim the guarantee conditions. To be able to guarantee a good and regular maintenance, we advise the
owner/user at strongest to make an appointment with DiBO against reaching the given up company hours,
concerning a maintenance turn.
6.3 Description daily control
6.3.1. Trailer
GENERAL: Check the frame entirely for screws coming loose, cracks and/or breakages of the welded joints.
Keep the machine as clean as possible to avoid dirt, water, oil and spilled fuel having a unfavourable effect.
Double check the tire tension, brakes and signalling.
This is necessary for your own and other peoples safety on the road.
6.3.2. manometer
$WDQVZLWFKHGRIIPDFKLQHWKLVPHDQVDKDOWHGHQJLQHWKHPDQRPHWHUPXVWUHÀHFWEDU
t an maximum performing machine, this means operated at full load working engine, the manometer can not
indicate more than the maximum pressure by DiBO indicated, for your machine.
After operation and releasing the gun can still remain a small pressure remainder present.
7KHUHÀHFWHGYDOXHRIWKHPDQRPHWHUPXVWEHEHWZHHQEDUWKHYDOYHVDUHWKHQDOOULJKW
6.3.3. High pressure pump
Check the pump on loose connections, bolts, seals and leaks.
Check regularly the oil level of the pump. If the oil level has decreased too much or pollution of oil is ob-
served, should these be replaced before working further.
Puts the machine on a horizontal base. The oil level must stand halfway the level glass.
Take at doubt the oil level stick separately, where the oil level must stand between both mark lines.
If pump oil gives a milky impression, frequently indicates this on an internal leak as a result of which water
touched oil there.
Immediately repair
is necessary then.
6.3.4. High pressure and low pressure parts
Check the hoses, piping and connections on external damages and leaks.
If damaged or leaks these must be immediately replaced.
6.3.5. Spray tools
Check lances and guns on leaks, external damages and hair cracks.
If damaged or leaks these must be immediately replaced.
Check the spray image of the water jet, if these blows out to much you must replace the nozzle.
Check protective cap-nozzle on damages and replace if necessary.
Check the thread of the couplings on external damages. At damage let these replace without delay.
6.3.6. Water tank
Check the water tank on external damages and leaks.
&KHFNZKHQWKHWDQNLV¿OOLQJLIWKHÀRDWV\VWHPZRUNVSURSHUO\
6.3.7. Frame
Check the frame in its entirety at loose bolts and/or cracks of the welds.
Keep the machine as much as possible clean to prevent act on dirt, water, oil and messed fuel.
6.3.8. Oil drainage high pressure pump
Put a oil trough under the drain plug. Remove the drain plug.
Let all the oil in the oil trough. Assemble the drain plug (with a new packing ring).
Содержание JMB-R 100/40 Series
