CC7574DKV OPERATOR’S MANUAL
6. Inspect the flange assembly and clean or
replace dirty/damaged components.
7. Carefully fit the outer flange back into the
inner flange and/or blade shaft.
8. Place the wedge lock washer onto the
blade shaft screw and insert the screw into
the blade shaft through the center of the
outer flange.
9. Retighten the blade shaft screw to secure
the flanges.
10. Remove the detent pin (guards 26” and up)
from the guard hinge and pivot the front of
the guard down over the blade flanges to
secure.
11. Re-insert the detent pin.
Engine
WARNING
Operate the saw in well-ventilated
areas. Concentrated engine
exhaust can cause loss of
consciousness and/or death.
DO NOT touch the engine/muffler with the
engine running, and always let them cool
down prior to touching or servicing the
saw.
DO NOT leave the saw unattended while the
engine is running
.
Tasks Prior to Starting the Engine
Complete the tasks listed below prior to
starting the engine to ensure a safe start:
•
Check fluids and fill to appropriate levels.
•
Turn off controls and switches.
•
Remove tools from area.
The engine
will not
start unless the following
tasks are completed:
•
Place speed control lever to the
STOP/PARK
position.
•
Pull up emergency stop button.
•
All emergency stop triggers are cleared:
1) E-Stop active
2) Low coolant level
3) Radiator door open
Starting the Engine
Notice: In an emergency, press the
emergency stop button to immediately stop
the engine and any saw movement
!
1. Insert the key into the ignition and turn it to
the
ON
position and wait for the display
screen to energize.
NOTE: While the display screen is energizing,
the glow plug is preheating. If the glow plug
requires more preheat time the following pop-
up message will appear: “Wait to start,
preheating”.
2. Once the display screen is energized and
there are no pop-up messages, turn the
key to the
START
position and release
when the engine starts.
NOTE: If the engine does not start within 10
seconds, turn off the key and try again
approximately 30 seconds later. Refer to the
engine manual for troubleshooting
recommendations after several failed attempts
.
3. Let the engine warm up. Check all warning
lights and turn off the engine immediately if
there are any problems prior to operating
the saw.
4. Increase/decrease the engine/blade speed
by pressing the throttle switch up or down
as needed.
Stopping the Engine
CAUTION
•
DO NOT leave the saw unattended until
the engine is off and the blade has
stopped spinning.
1. Place the speed control lever at
Stop
and
raise the blade from the cut.
2. Turn off all controls, switches, and water.
3. Decrease the engine speed to idle for five
minutes to cool down the engine after full
load operation.
4. Turn the ignition key to
Stop
and remove
the key.
35
Содержание CC7574DKV
