Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 93

Страница: 93 / 111

Dialogic

DSI SPCI Network Interface Boards Programmer's Manual Issue 5

run_mode

Protocols selected to Run on the Board

DTI

Digital Trunk Interface only, no protocol software. This mode does NOT
require the use of a software license button).

MTP2

MTP2 protocol only.

MTP

MTP3 plus MTP2 protocols.

ISUP-S

ISUP, small version, plus all MTP.

ISUP

ISUP, regular version, plus all MTP.

ISUP-L

ISUP, large version, plus all MTP.

TUP-S

TUP, small version, plus all MTP.

TUP

TUP, regular version, plus all MTP.

TUP-L

TUP, large version, plus all MTP.

DTI

Digital Trunk Interface only, no protocol software. This mode does NOT
require the use of a software license button).

MTP2

MTP2 protocol only.

MTP

MTP3 plus MTP2 protocols.

See section 2.3.2

Capacity

for details of the capacity for modules running on

the DSI SPCI Boards.

7.1.2

LIU_CONFIG Command

Syntax:

LIU_CONFIG <board_id> <liu_id> <liu_type> <line_code>

<frame_format>

<crc_mode>

Example:

LIU_CONFIG 0 0 5 1 1 1

This command is used during initialization to configure the operating
parameters for a T1/E1 line interface unit.

<board_id>

The logical identity of the board in the range from 0 to one less than the
number of boards supported.

<liu_id>

The identifier of the T1/E1 Line Interface Unit in the range from 0 to one less

than the number of interfaces supported.

Note:

For the SPCI2S, valid values for the LIU identifiers are 2 and 3.

<liu_type>

The physical type of interface according to the following table: (note that this
must be selected by the user to be appropriate for the actual hardware fitted

otherwise an error status is returned).

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды