Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 111

background image

4 Configuration and Operation

26

4.4

Board Information Diagnostics

To assist in diagnosis of configuration problems and reporting hardware

details when encountering problems, a diagnostic display feature is available

in s7_mgt.

When s7_mgt is run with the –d command line option, a diagnostic display of

board hardware parameters is generated in this format following

configuration of the board.

S7_MGT Board identification: board_id 0
  Board type: 2 (SPCI)
  Hardware revision: 0
  RAM size: 0x00000000
  Interface type: 0
  RTB switch: 0
  ADDR switch: 0
  BOOT switch: 8
  Shelf: 0
  Slot: 0
  Firmware: V1.02
  Electronic serial number: 01-000007e09eb9-8a
  License serial number: 02-0000008c92f7-72

The parameters are as described below:

Table 9: Board Diagnostics – Hardware Parameters

Parameter

Description

Board type

Board types are reported as follows:

2

SPCI2S or SPCI4

Hardware revision

The board hardware revision number.

RAM size

The on-board RAM size.

Interface type

Parameter not supported for DSI SPCI Boards. Value
returned equals 0.

RTB switch

Parameter not supported for DSI SPCI Boards. Value
returned equals 0.

ADDR switch

Geographic addressing switch setting, that is, the
address at which the board appears when the –o3
feature of ssds is used.

BOOT switch

The setting of the board's rotary switch labeled “Boot”.

Default setting - 8.

Shelf

Parameter not supported for DSI SPCI Boards. Value
returned equals 0.

Slot

Parameter not supported for DSI SPCI Boards. Value
returned equals 0.

Firmware

Firmware revision number.

Electronic serial number

The board's electronic serial number.

License serial number

License serial number. The serial number of the fitted
license button (all zero's if none found).

«
...
24
25
26
27
28
...
»

Содержание DSI SPCI Network Interface Boards
















































































































Отзывы:

Нет отзывов

Похожие инструкции для DSI SPCI Network Interface Boards

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 7

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

X-Pedition 2000

Бренд: Enterasys Страницы: 86

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Бренд: Keithley Страницы: 98

Бренд: National Instruments Страницы: 130

ExpressBox2 EB2

Бренд: Magma Страницы: 74

Бренд: Alcatel-Lucent Страницы: 60

Бренд: Paradyne Страницы: 1

Modem/Router ADSL BIPAC-7100

Бренд: Billion Страницы: 13

Бренд: Asus Страницы: 21

Бренд: Asus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды