Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 18

Страница: 18 / 111

3 Installation

To enable this functionality the following line must be added to the
/etc/system file:

set sptpci:spt_claimint=1

The system has to be rebooted to force the change to take effect.

3.5.5

Removing the Development Package for Solaris

The Development Package for Solaris is removed using the package removal
utility:

pkgrm <dpksol32 / dpksol64>

The Solaris package removal utility (pkgrm) then prompts for further input.

On successful completion of the procedure the following message is displayed

and the user should reboot the system:

Removal of <dpksol32 / dpksol64> was successful.

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды