Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 73

Страница: 73 / 111

Dialogic

DSI SPCI Network Interface Boards Programmer's Manual Issue 5

dest_stream

The

destination stream

references which of the CT bus streams is used as a

destination for the data. The parameter takes values in the range 0…31.

dest_slot

The

destination slot

references the CT bus timeslot to which a local stream

timeslot can be connected or disconnected. The destination slot value has the

same range as the

source slot

pattern

The value of the fixed data to be generated. The value must be in the range 0

to 255. Typical values are 0xff for an "all ones" idle pattern, or 0x2a for an

ITU-T E1 idle pattern.

Status Response

The confirmation message (if requested) indicates success by status of zero.

On error, the following status values can be found in the confirmation

message.

Value

Mnemonic

Description

0xd2

MVIP_INVALID_STREAM

Invalid stream specified in listen request.

0xd3

MVIP_INVALID_TIMESLOT

Invalid timeslot specified in listen request.

0xff

None

Invalid message length.

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды