Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 111

background image

Dialogic

®

DSI SPCI Network Interface Boards Programmer's Manual Issue 5

55

frame_format

Description

1

E1 double frame (E1 only).

2

E1 CRC4 multiframe (E1 only).

4

D3/D4 (Yellow alarm = bit 2 in each channel) (T1 only).

7

ESF (Yellow alarm in data link channel) (T1 only).

crc_mode

The CRC mode taken from the following table:

crc_mode

Description

1

CRC generation disabled.

2

CRC4 enabled (frame_format must be set to 2).

3

CRC4 compatibility mode (frame_format must be set to 2).

4

CRC6 enabled (frame_format must be set to 7).

build_out

Configurable line build out is not supported by the board, so the following

fixed values must be used.

Build_out

Description

0

Setting for E1 devices.

1 Setting

for

T1

devices.

faw

The 8 bit value to be used for any E1 frame alignment word bit positions that
are not modified by other options. This allows the spare bit designated "For

International Use" to be set by the user when CRC4 mode is disabled. Valid
values are 0x9b or 0x1b. When using T1, this parameter must be set to zero.

[E1 default = 0x9b].

nfaw

The 8 bit value to be used for any E1 non-frame alignment word bit positions

that are not modified by other options. Normally, this parameter is set to

0x9f for E1 operation and set to zero for T1.

ais_gen

The (initial) mode used to generate the Alarm Indication Signal (Blue Alarm)

taken from the following table. The user may subsequently modify the setting

of the outgoing signal using the LIU_MSG_CONTROL message.

ais_gen

Description

1

Disabled - do not generate AIS / Blue alarm.

2

Enabled - generate AIS / Blue alarm.

«
...
53
54
55
56
57
...
»

Содержание DSI SPCI Network Interface Boards
















































































































Отзывы:

Нет отзывов

Похожие инструкции для DSI SPCI Network Interface Boards

Бренд: D-Link Страницы: 83

Бренд: Opengear Страницы: 2

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Бренд: WAGO Страницы: 48

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

Бренд: QTech Страницы: 406

NVR41-4KS2 Series

Бренд: Dahua Страницы: 452

Бренд: Planet Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: Amphenol Страницы: 43

TeleLite 720920 Series

Бренд: Positron Страницы: 21

Бренд: National Instruments Страницы: 37

Бренд: Billion Страницы: 2

Бренд: Acrosser Technology Страницы: 42

12000 - Series Chassis Modular Expansion Base

Бренд: Cisco Страницы: 602

Бренд: Digi Страницы: 2

Бренд: Kraun Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды