Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 41

Страница: 41 / 111

Dialogic

DSI SPCI Network Interface Boards Programmer's Manual Issue 5

Description:

This message is used during initialization (or re-configuration) by the

application to reset a board and download the code file that contains the

operating software for the board.

The download operation is supervised by the device driver that reads the
binary format code file and transfers it to the board.

The confirmation message (if requested) indicates success by status of zero.

This implies that the reset operation has commenced but does not imply
completion. The application must then wait until a

Board Status Indication

is received. This indicates either successful completion of the reset and

download operation or failure during the procedure.

Parameter Description:

board_type

The type of board to be reset. This must be set to 2 for DSI SPCI Boards.

phy_id

The physical ID for the DSI SPCI Board. This field must be set to the same

value as the board_id. (i.e., 0 … one less than the number of boards

supported).

code_file

Null terminated string giving the filename of the code file to be downloaded to

the board.

run_mode

Number taken from the following table to indicate which protocols are to be

run.

Note:

It is only possible to activate protocols that have been licensed to run on the
board

by use of a suitable license button.

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды