Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 6

Страница: 6 / 111

Revision History

Issue

Date

Description

12-Apr-00

Initial release for evaluation purposes. Some sections incomplete.

20-Apr-00

Several minor corrections especially relating to LIU configuration and
switching. Addition of installation section for Windows

NT.

30-Jul-01

Sections detailing support for Windows

2000, Linux and Solaris added.

Additional messages to read LIU state, indicate clock events and s7_mgt
completion status.

06-Jan-03

Branding changed to Intel

NetStructure™. Septel PCI now SPCI4 / SPCI2S

and Septel cP now CPM8. References to NUP protocol removed.
INAP_API.LIB added.

3 23-May-05

Remove

INAP_API

module.

Change name of package in Solaris DPK to <dpksol32.Z / dpksol64.Z >.

Add geographic addressing, gctload as a service, watchdog timer, Linux
driver source code release.

Added board Option Switch / Link settings, General Module Identification
Message and Read Board Info Request Message and Set on-board LED's
Message.

Add capacity section and support for Windows

XP.

05-Mar-09

Removed CPM8 specific content as product is now EOL.

Updated to Dialogic

branding. Refreshed operating system support and

documented new “bundled” license button set and corresponding run
modes.

20-Mar-09

Clarification to ISUP-S and TUP-S protocol dimensioning.

Note:

Current software and documentation supporting Dialogic

DSI SPCI Network

Interface Boards is available at:

http://www.dialogic.com/support/helpweb/signaling

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды