Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 81

Страница: 81 / 111

Dialogic

DSI SPCI Network Interface Boards Programmer's Manual Issue 5

Description:

This message is issued by s7_mgt on completion of the initial configuration

sequence and indicates either success (status=zero) or an error condition

that occurred during configuration. The message is only issued when s7_mgt
is run with the

–i

command line option specifying the module_id of the

Notification Module

to which the message is sent. For example:

s7_mgt

–i0x2d

Note:

It is recommended that the user invoke this option and then wait for the

API_MSG_CNF_IND message to ensure the application does not attempt to send

messages until initial configuration is complete.

Parameter Description:

Completion Status

The result of initial configuration coded as follows:

Value

Meaning

0 Success

Error opening config.txt file

Syntax or value error in config.txt file

Error during configuration (invalid parameters)

Error during configuration (no response)

6.4.3

Clock Event Indication

Synopsis:

Message issued by the board to indicate on-board clocking related events.

Message Format:

MESSAGE HEADER

Field Name

Meaning

type MVD_MSG_CLK_IND

(0x0e23)

src MVD_TASK_ID

dst

0xdf

rsp_req

hclass

status Event

(see below)

err_info

Reserved for future use

len

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды