Dialogic DSI SPCI Network Interface Boards Скачать руководство пользователя страница 68

Страница: 68 / 111

6 Message Reference

timeslot

The timeslot number on the T1/E1 line interface unit on which the fixed data

is transmitted. The valid range for

timeslot

is 1 to 31 for an E1 interface and

1 to 24 for a T1 interface.

pattern

The value of the fixed data to be generated. The value must be in the range 0

to 255. Typical values are 0xff for an "all ones" idle pattern, or 0x2a for an

ITU-T E1 idle pattern.

Status Response

The confirmation message (if requested) indicates success by status of zero.

On error, the following status values can be found in the confirmation
message.

Value

Mnemonic

Description

0xd2

MVIP_INVALID_STREAM

Invalid stream specified in listen request.

0xd3

MVIP_INVALID_TIMESLOT

Invalid timeslot specified in listen request.

0xff

None

Fixed pattern generation request failed.

6.3.9

Reset Switch Request

Synopsis:

Resets the digital switch to its default state in accordance with the current

board configuration.

Message Format:

MESSAGE HEADER

Field Name

Meaning

type MVD_MSG_RESETSWX

(0x7e00)

src

Sending Module ID

dst MVD_TASK_ID

(0x10)

rsp_req

used to request a confirmation

hclass

status

err_info

len

Содержание DSI SPCI Network Interface Boards
















































































































Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды

Dialogic DSI SPCI Network Interface Boards, Руководство программиста

Результаты поиска

Содержание DSI SPCI Network Interface Boards

Отзывы:

Похожие инструкции для DSI SPCI Network Interface Boards

Бренды по названию

Популярные бренды