background image

Dialogic

® 

DSI SPCI Network Interface Boards Programmer's Manual Issue 5 

103 

<num_grps> 

The maximum number of ISUP circuit groups that the user intends to use. 

This must not exceed the maximum number of circuit groups supported 

otherwise module configuration will fail. Typically <num_grps> would be set 

to the maximum number of circuit groups supported. 

<num_ccts> 

The maximum number of ISUP circuits that the user intends to use. This must 

not exceed the maximum number of circuits supported otherwise module 
configuration will fail. Typically <num_ccts> is set to 32 times the number of 
groups for E1 operation and 24 times the number of circuit groups for T1 

operation. 

Note:

   The valid range for the circuit identifier (cid) is from zero up to one less than the 

maximum number of circuits (num_ccts). 

<partner_id> 

Optional parameter for use when operating in dual resilient configuration. 
This parameter is the module_id of the ‘partner’ ISUP module (equivalent to 

the ‘module_id field in the ISUP Configure Request message as documented 

in the ISUP Programmer’s Manual). 

7.3.2

 

ISUP Circuit Group Configuration 

Syntax:  

ISUP_CFG_CCTGRP <gid> <dpc> <base_cic> <base_cid>  
<cic_mask> <options> <user_inst> <user_id> <opc> 

<ssf> <variant> <options2> 

Example: ISUP_CFG_CCTGRP 

1 1 0x7fff7fff 0x00000003 0 0x2d 

2 0x8 4 0x00000000

 

The configuration parameters for a group of ISUP circuits. Usually a group is 

all the circuits on a single E1 or T1 interface. 

<gid > 

The group id of the circuit group in the range 0 to one less than the number 

of groups supported. 

<dpc> 

The destination point code for all circuits in the circuit group. 

<base_cic> 

The Circuit Identification Code (CIC) that is allocated to the first circuit in the 

circuit group. 

<base_cid> 

The logical id for the first circuit in the circuit group. It must lie in the range 0 

to one less than the number of circuits supported. 

Содержание DSI SPCI Network Interface Boards
















































































































Отзывы: