manualshive.com logo in svg

DGSHAPE DWX-42W, Руководство по установке

Поделиться
Скачать
DGSHAPE DWX-42W Скачать руководство пользователя страница 59

57

2. Installation and Setup

2. Connecting to the Computer

Step 8 : Disconnecting the USB Cable

•  Remove the USB cable from the cable clamp.

Cable clamp

Step 9 : Connecting the LAN Cable

•  Prepare a LAN cable (Category 5 or higher) separately.
•  We recommend 100BASE-TX for the Ethernet.

Important

•  Do not bind the LAN cable with the cable clamp.
•  Wire the LAN cable so that it does not touch the USB cable or the power cord.

The LAN cable coming into contact with other cables will result in communication errors due to electrical 
noise.

Connecting the Computer and the Machine Directly

Connecting through a LAN hub

LAN hub

Important: Do not connect any device other than the machine and a computer to the LAN hub.

Do not connect any device other than the designated machine and a computer to the LAN hub being 
used here. Connecting any other device will prevent the settings from being configured correctly and 
may cause problems with the network settings of connected devices.

Содержание DWX-42W





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды