manualshive.com logo in svg

DGSHAPE DWX-42W, Руководство по установке

Поделиться
Скачать
DGSHAPE DWX-42W Скачать руководство пользователя страница 50

48

2. Installation and Setup

2. Connecting to the Computer

Step 3 : Switching the Power On

Procedure

A 

Connect the power cord.

WARNING

 

Connect to an electrical outlet that complies with this machine’s ratings (for 
voltage, frequency, and current).

Incorrect voltage or insufficient current may cause fire or electrical shock.

WARNING

 

Handle the power cord, plug, and electrical outlet correctly and with care. Never 
use any article that is damaged.

Using a damaged article may result in fire or electrical shock.

WARNING

 

When using an extension cord or power strip, use one that adequately satisfies 

the machine’s ratings (for voltage, frequency, and current).

Use of multiple electrical loads on a single electrical outlet or use of a lengthy 

extension cord may cause fire.

WARNING

 

Connect to ground.

This can prevent fire or electrical shock due to current leakage in the event of a malfunction.

WARNING

 

Connect this machine to a power outlet. Never connect this machine directly to 

a power distribution panel or other such fixed wiring equipment.

Doing so increases the risk of fire or electrical shock.

Power cord

Power outlet

Содержание DWX-42W





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды