manualshive.com logo in svg

DGSHAPE DWX-42W, Руководство по установке

Поделиться
Скачать
DGSHAPE DWX-42W Скачать руководство пользователя страница 36

34

2. Installation and Setup

Step 1  : Deciding on an Installation Site

Placement and Installation

The weight of the machine alone is 61 kg (135 lb.). Unload and place the machine with care.

WARNING

 

Unloading and placement are operations that must be performed by 2 persons or more.

Tasks that require undue effort when performed by a small number of people may 
result in physical injury. Also, if dropped, such items may cause injury.

CAUTION

 

When lifting the machine, hold the locations shown in the figure.

Installation Environment

WARNING

 Install 

in a level and stable location.

Failure to do so may result in falling of the machine, leading to injury.

WARNING

 

Never install the machine in a location exposed to open flame.

Milling  waste  may  ignite.  Powdered  material  is  extremely  flammable,  and  even 
metal material may catch fire.

WARNING

 

Never install the machine close to any flammable object or in a gas-filled location.

Combustion or explosion may occur.

WARNING

 

Never install this machine outside or in any location where exposure to water or 
high humidity may occur.

Current leakage may cause electrical shock or fire.

WARNING

 Position so that the power plug is within immediate reach at all times.

This is to enable quick disconnection of the power plug in the event of an 
emergency. Install the machine next to an electrical outlet. Also, provide enough 
empty space to allow immediate access to the electrical outlet.

•  Never install the machine in a location subject to wide fluctuations in temperature or humidity.
•  Never install the machine in a location subject to shaking or vibration.
•  Never install the machine in a dusty or dirty location.
•  Never install the machine in a location exposed to direct sunlight or near air-conditioning or heating 

equipment.

•  Never install the machine in a location exposed to considerable electrical or magnetic noise or other forms 

of electromagnetic energy.

•  Never install this machine in an environment where silicone substances (oil, grease, spray, etc.) are present. 

Doing so may cause poor switch contact.

1. Installation

Содержание DWX-42W





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды