manualshive.com logo in svg

Desoutter CVIL II, Руководство оператора, Страница: 49 / 80

Поделиться
Скачать
Desoutter CVIL II Скачать руководство пользователя страница 49

01/2018

49 / 80

6159933780

Issue no: 09

CVIL II

8.1.4.2 - Calibration service

For full certified calibration, to cover your quality systems 

needs please consult your local Desoutter Customer 

Service Center that are fully prepared to support you, 

either at your site or in one of our workshops.
Being the equipment manufacture we are prepared not 

only to provide the calibration service and certification, 

but also to adjust your equipment for its fullest 

performance.
Our labs can provide you with either a local traceability 

chain to National standards or a International level, 

through ISO 17025 certified labs.

8.1.5 - Options

Contact your Desoutter representative for support.

8.1.6 - BRDx2 - controller backup

The minimum software version of the controller 

must be: V 5.1.A9.

Use this device to clone a controller.
Both configuration and firmware are copied during the 

process.
Before restoring, check that the target controller is not 

connected to the same Ethernet network as the source 

controller as this may cause a conflict between IP 

addresses.
Connect the BRDx2 to the serial port of the controller as 

described in the user manual 6159922590.
Go to the Maintenance menu and select “BRDx2”.

8.1.6.1 - Backup

8.1.6.2 - Restore

8.2 - SERVICE menu

See "Start up", page 11.

Содержание CVIL II

















































































Отзывы:

Нет отзывов