manualshive.com logo in svg

Desoutter CVIL II, Руководство оператора, Страница: 34 / 80

Поделиться
Скачать
Desoutter CVIL II Скачать руководство пользователя страница 34

01/2018

34 / 80

6159933780

Issue no: 09

CVIL II

7.7.3 - INPUT menu

Do not change SCY and DIR settings.

Inputs

Name

Factory 

config.

Comments

Cycle 1 selection CYC1

X

Binary coding - weight 1, i.e. from 0 to 1.

Cycle 2 selection CYC2

X

Binary coding - weight 2, i.e. from 0 to 3.

Cycle 4 selection CYC4

X

Binary coding - weight 4, i.e. from 0 to 7.

Cycle 8 selection CYC8

X

Binary coding - weight 8, i.e. from 0 to 15.

Cycle 16 selection CYC16

Binary coding - weight 16, i.e. from 0 to 31.

Spindle validation SPVAL

X

Validates - or not - the tool start in both tightening directions if "Sp. val." 

is enabled in the Station Menu.

Tightening 

direction 

validation

VPSTIG

Validates - or not - the tool start in the tightening direction if"Sp. val." is 

enabled in the Station Menu.

Run reverse 

direction 

validation

VPSLOO

Validates - or not - the tool start in the run reverse direction if "SpV.rrv" is 

enabled in the Station Menu.

Error 

acknowledgement

ACKNOW

Validates again the tool operation after a reject report if the error 

acknowledgement function in the Station Menu is enabled.

Start cycle

SCY

X

The cycle is run as long as the signal is at 1.
When the signal drops, the cycle stops and the report is sent to the PLC.

Tightening / Run 

reverse

DIR

X

Validates the un-tightening direction as soon as the Start Cycle signal 

appears, at the speed programmed in the Station Menu and with the 

maximum current of the tool.

Reset

RESET

X

This signal resets the tightening reports and deletes the results 

displayed.

External stop

EXSTOP

When the parameter is programmed on Yes in the programming screen 

of the run down speed, final speed and run reverse phases, the system 

stops the current phase on a pulse and switches to the next one.

Содержание CVIL II

















































































Отзывы:

Нет отзывов