manualshive.com logo in svg

Desoutter CVIL II, Руководство оператора, Страница: 36 / 80

Поделиться
Скачать
Desoutter CVIL II Скачать руководство пользователя страница 36

01/2018

36 / 80

6159933780

Issue no: 09

CVIL II

7.7.4 - OUTPUT menu

Outputs

Name

Factory 

config.

Comments

Cycle 1 

acknowledgement

CYC1

X

Binary coding -weight 1. The cycle acknowledgement is sent back only if 

it corresponds to a programmed cycle; otherwise it is at "0".

Cycle 2 

acknowledgement

CYC2

X

Binary coding -weight 2. The cycle acknowledgement is sent back only if 

it corresponds to a programmed cycle; otherwise it is at "0".

Cycle 4 

acknowledgement

CYC4

X

Binary coding -weight 4. The cycle acknowledgement is sent back only if 

it corresponds to a programmed cycle; otherwise it is at "0".

Cycle 8 

acknowledgement

CYC8

X

Binary coding -weight 8. The cycle acknowledgement is sent back only if 

it corresponds to a programmed cycle; otherwise it is at "0".

Cycle 16 

acknowledgement

CYC16

Binary coding -weight 16. The cycle acknowledgement is sent back only 

if it corresponds to a programmed cycle; otherwise it is at "0".

Pass Through

PTHRU

Allows the PLC to drive the output directly.

Maintenance

MAINT

In case a maintenance is requested (tool counter reached or 

maintenance date).

Ready

READY

X

This signal is at "1" when the controller is in working order.

In cycle

INCYC

X

Response to the Start Cycle request. Drops to "0" at end of cycle.

Global report OK

ACCRP

X

Sent to the PLC when the cycle is over and the global report is OK.

Global report NOK REJRP

X

Sent to the PLC when the cycle is over and the global report is NOK.

Number of cycles 

OK

NCYOK

X

This signal switches to "1" when the number of cycles run with an Accept 

report is equal to the programmed number of cycles OK.

This output is reset after the "RP duration" time set in the 

"Station - general parameters" menu.

Synchronization

SYNC

The synchronization signal falls down at the end of the phase and is 

used, connected with synchronization of other controllers to synchronize 

the next phase (see "Synchronizing several cvil controllers", page 52).

Torque report OK TOROK

Sent to the PLC when the cycle is over and the torque report is OK.

Torque report NOK TORNOK

Sent to the PLC when the cycle is over and the torque report is NOK.

Angle report OK

ANGOK

Sent to the PLC when the cycle is over and the angle report is OK.

Angle report NOK ANGNOK

Sent to the PLC when the cycle is over and the angle report is NOK.

Содержание CVIL II

















































































Отзывы:

Нет отзывов