manualshive.com logo in svg

Desin Instruments HS-7000 Series, Общее руководство по инструкции

Поделиться
Скачать
Desin Instruments HS-7000 Series Скачать руководство пользователя страница 9

9

FORMATS

This Series is presented in 3 different formats, provided with the same functions, the only
difference between the models is the format.

HS-7200

1/8 DIN Horizontal Indicator, with dual 6 and 4-digit
display respectively. Suitable for displaying
measured and calculated variables.

HS-7300

1/8 DIN Vertical Controller, with 3 x4-digit display.
Suitable for multivariable process control.

HS-7500

DIN Rail mounting processor, without display and
keypad format.
Suitable remote multivaraible control from PC.

The 

HS-7200

 and 

HS-7300

 could be programmed from front keypad or from PC using the

LoopWin Programming Tool Software.

The 

HS-7500

 can only be programmed by LoopWin, since it is not provided with keypad.

These devices are provided with 2 independent RS-485 ports, having same address and
communication speed rate to be Controlled, conneced to a Modbus terminal in the field, and
at the same time, Supervised by the Proasis DCS-Win or Proasis LAN-Win software as well as
by any other SCADA software Modbus compatible.

These instructions describes models provided with factory standard configuration. Modifications
could be done by the user by LoopWin or keypad, depending on the model used.

STANDARD CONFIGURATIONS:

HS-7200

3 mV or mA inputs (2 configured as TC and Pt 100); with 6 alarms and 4 relay
outputs, and 2 signal retransmission 4-20 mA outputs.

HS-7300

3 mV or mA inputs (2 configured as TC and Pt 100); with 3 PID loops, 6 alarms and
4 relay outputs, and 2 control 4-20 mA outputs.

HS-7500

3 mV or mA inputs (2 configured as TC and Pt 100); and 2 signal retransmission
4-20 mA outputs.

NOTE

: Only one of the two inputs is used for TC input, since the second one is used for CJC (Cold

Junction Compensation using a Pt 100).

Содержание HS-7000 Series













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды