Desin Instruments HS-7000 Series Скачать руководство пользователя страница 19

Страница: 19 / 108

LED

F1 and F2

Indicate the status of the Loop displayed at present.

When On (lit), indicates Manual mode. When Off (unlit) indicates AUTO mode. When

flickering indicates Hold mode due to PID control failure.

Indicates Remote Setpoint, and the signal in AI 3 is the current setpoint .

NOTE:

All the LEDs Y or F can be used to indicate the status of any internal logic variable

. For other functions refer to the Advanced Programming Manual.

FUNCTION

Key

Allows to scroll, in the MENU, all the enabled functions.

Allows to exit from any parameter without saving the changes if any.

If pressed, cancels the PID Autotuning progress.

INCREMENT

Key

Allows to increase the value of the flickering digit.

During online edition, increase the value of the flickering parameter on the display.

In other functions, modify the option if allowed.

SHIFT

Key

During edition, allows to select the digit to modify (flicker), shifting to the left digit by
digit.

During online edition, decreases the value of the flickering parameter on the display.

ENTER

Key

Used to access to a function or parameter of the MENU.

When a parameter is modified, save the changes realized.

PROGRAMMABLE

Key *

Allows to shift from Auto to Manual and vice versa, in Auto-Manu function of each loop.

Can be used to Activate, Inhibit, etc the Hold, Integrator, Counter, etc. functions.

By programming, any other action or function could be assigned to this key.

PROGRAMMABLE

Key

Allows to shift from Local to Remote Setpoint and vice versa, in Local-Remote function
of each loop.

Can be used to Reset, Zeroing, etc. the Hold, Integrator, Counter, etc. functions.

By programming, any other action or function could be assigned to this key.

Содержание HS-7000 Series













































































































Результаты поиска

Содержание HS-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Desin Instruments HS-7000 Series, Общее руководство по инструкции

Результаты поиска

Содержание HS-7000 Series

Отзывы:

Бренды по названию

Популярные бренды