• Desmontar la Caja del quemador (F. Fig. 5), para identi
fi
car la
bomba del quemador (O Fig. 6);
• Desatornille la tuerca (A Fig. 11) eso que bloquea el elemento
fi
ltrante a la bomba;
• Extraiga el elemento
fi
ltrante (C Fig 11);
• Limpiarlo perfectamente con aire comprimido y gasóleo.
No
utilizar agua;
• Inserte el elemento
fi
ltrante nuevamente dentro de su lugar y
atornille la tuerca a la bomba.
LIMPIEZA DEL QUEMADOR XL9 E
• Retirar los tornillos (H Fig. 5) de
fi
jación del quemador, a la
placa soporte de la cámara de combustión.
• Quitar el quemador de la cámara de combustión.
• Retirar los tres tornillos (B Fig. 12) de
fi
jación del tubo del que-
mador (
A
Fig. 12).
• Retirar el tubo girándolo en sentido contrario a las agujas del
reloj, según se mira al quemador (Fig. 12).
• Retirar los tornillos (
C
Fig.12) que sujetan el conjunto disco lla-
ma -electrodos y deslizarlo sobre el porta-boquilla (ver Fig.13)
• Limpiar el disco llama (
D
fi
g.14) y los dos electrodos (
E
Fig.14)
sustituyéndolos si fuese necesario.
• Quitar la boquilla (G Fig.14) del porta-boquillas (F Fig.14) para
limpiarla bien y si fuese necesario sustituirla por otra de las
mismas características.
• Colocar de nuevo la boquilla (G Fig. 14) ya limpia en su aloja-
miento.
• Colocar el conjunto disco llama-electrodos, ajustando con
sumo cuidado todos los reglajes que se indican en la
fi
g 14.
• Finalmente, colocar el tubo de protección y
fi
jar el quemador a
la cámara de combustión.
ACCESORIOS OPCIONALES
TERMOSTATO AMBIENTE
Conexión del Termostato ambiente
ATENCION: Antes de conectar los elementos de control
se debe: apagar el generador según las indicaciones
descritas en el apartado correspondiente de este Manual
“APAGADO DEL GENERADOR”, esperar el tiempo de
post-ventilación para su enfriamiento y desenchufar la
conexión eléctrica de la red.
Para conectar el termostato ambiente se necesita:
• Quitar la caperuza
D
de la toma de conexión
A
• Retirar los tornillos
B
y sacar el cuerpo interior
C
• Desconectar el puente y conectar los cables del termostato
ambiente a las clemas 2 y 3.
• Colocar el cuerpo
C
dentro de la base
A
y apretar los tornillos
B
• Insertar el enchufe
E
del Termostato Ambiente.
FILTRO PRE-CALENTADOR DE COMBUSTIBLE
RUEDA APOYO
ACCESORIOS OPCIONALES
28
ES
D.
C.
A.
B.
E.
A.
C.
B.
C.
A.
tubo del
quemador
B.
tornillos
C.
tornillos
C.
tornillos
Figura 12 - tubo del quemador XL9
.
Figura 13 - Conjunto disco llama - electrodos y deslizarlo
sobre el porta-boquilla XL9.
C .
D .
4 m m
4 m m
6-
7mm
E.
F.
G .
22 m m
Figura 14 - disco llama-electrodos.
D.
disco llama,
E.
electrodos,
F.
porta-boquillas,
G.
Boquilla