manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 86

 

86 

10  Operations using the Web-based User Interface 

10.1 Requirements 

10.1.1 Hardware 

The web interface operates on any common PC or Notebook with a network card or a 
WLAN card. 

10.1.2 Software 

The web-based user interface can be used with any common operating system, such 
as MS Windows, Linux, OS X ..., and functions with all common, current browsers. 

10.1.3 Connecting to the AST40 sequence controller  

The computer on which the web-based user interface is running can either be connected 
directly to the AST40 sequence controller or can be connected via a common network.  
In the case of a direct connection, both crossed and uncrossed cables can be used; the 
AST40 sequence controller independently recognizes it and establishes the connection 
accordingly. 

10.2  Preparing to use the web interface 

To use the web-based user interface, both the AST40 sequence controller and the 
browser must be installed in such a way that a TCP/IP connection between both of these 
can be established and the exchange of data is enabled. 

10.2.1.1  Setting up the AST40 sequence controller  

A fixed IP address must be set up in the AST40 sequence controller (also see 

9.2.5.2 

System setup

 and "Getting Started for Commissioning"). It must be assigned by the 

administrator of the local network. At the time of delivery the following values are preset: 
 

IP address of master control unit:  10.10.25.100 

 Subnet 

mask: 

 

255.255.0.0 

 Gateway: 

 

10.10.20.9 

10.2.1.2  Setting the browsers/operating systems 

The browser must have free access to the ASTS40 sequence controller, i.e.  

•  it must be possible to reach the IP address of the AST40 sequence controller. 
•  the HTTP protocol must not be deactivated 
•  a possible proxy must be disabled for the IP address for the AST40 sequence 

controller (or general local addresses). 

The browser must accept cookies from the AST40 sequence controller and the JavaScript 
must be activated. In case of doubts contact your responsible IT representative. 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды