manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 137

 

137 

15.1.3 Main controller 

Number  Meaning 

Trouble shooting 

201 

Fieldbus not available! 

Check that the fieldbus module is installed and 
mounted tightly. If the fieldbus module no 
longer needs to be used, deactivate the 
fieldbus in the settings. 

202 

Software versions of master control 
unit and power unit do not match! 

Please contact the DEPRAG Service 
Department. 

203 

Screwdriver and power unit do not 
match! 

Ensure that you have installed the correct 
screwdriver model to the

 AST40. 

204 

Settings have been lost, default values 
are being loaded 

Check the settings and adjust them if 
necessary. 

205 

Error in the data memory 

206 

Error in the communication power unit 

207 Bus 

internal 

error 

208 

No connection to fieldbus! 

Troubleshooting not possible 

209 

SSC-driver could not be loaded 

210 

Error during emergency stop 

Switch the AST40 off and on again. 

211 

Software versions of master control 
unit and power unit do not match! 

Please contact the DEPRAG Service 
Department. 

Table 47: 

System error - Master control unit 

 

15.1.4 Communication 

Number  Meaning 

Trouble shooting 

301 No 

connection 

302 General 

error 

303 Checksum 

error 

304 

Module not found 

305 Unknown 

command 

306 Timeout 
307 

Access to write-protected area 

308 

Value outside of limits! 

Switch the AST40 off and then restart again. 

Table 48: 

System error – Communication 

 

15.1.5 I/O interface 

The assignment of the inputs and outputs to the interfaces SPS1 (GX2) and SPS2 (GX3) 
can be found in 

6.2.7 I/O interfaces

. 

Number  Meaning 

Trouble shooting 

401 

Output "System OK" overloaded 

402 

Output "Ready" overloaded 

403 

Output "OK" overloaded 

404 

Output "NOK" overloaded 

405 

Output "Status HS Reserve" overloaded 

406 

Output "Emergency stop 2 active" overloaded 

407 

Output "Emergency stop 1 active" overloaded 

408 

Output "Screw cycle active" overloaded 

409 

Output "Screwdriving program 1" overloaded 

410 

Output "Screwdriving program 2" overloaded 

411 

Output "Screwdriving program 3" overloaded 

412 

Output "Screwdriving program 4" overloaded 

413 

Output "GX4: Pin 13 (not in use)" overloaded 

414 

Output "Status LT Reserve" overloaded 

415 

Output "GX4: Pin 6 (not in use)" overloaded 

416 

Output "GX4: Reload" overloaded 

Check the connections to the 
I/O interface 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды