manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 126

 

126 

13 Documentation 

13.1 Final values 

If the command 'save value' is used in the screwdriving program, then the screwdriving 
results are stored in a CSV data file and can be loaded from the controller via the web 
interface (see also 

10.3.5.1 Final values

). The command "save values" can be used as 

often as required within the screwdriving process, however, only the last three values 
whitin a single sequence are saved. In case of a fault or screwdriving error the final values 
are always saved. 

 

IMPORTANT 

The data is only available if the screwdriving program has received the 
command "save final values" or if a faulty screwdriving application is 
present.

 

One CSV data per day is saved automatically. All data from the previous seven days is 
always available. The final values of the screwdriving application that are older than seven 
days are overwritten by new final values. 

The final value data of the last screwdriving application are also saved in the file 
"actual.csv". 
The files are subject to the same limitations as described in chapter 

13.2 Curve display

 for 

the curve data. 
The CSV file is structured as follows: 

•  First line: Title bar with caption of the values (in files 1-7.csv only) 
•  Following lines: results of a screw assembly per line 

Value 

Description 

Date 

Date of screwdriving application 

Time 

Time of screwdriving application 

Programnumber Program 

used 

Status Status, 

also 

see 

15.2 Error in the Screwdriving Sequence

 

Total Time 

Total duration of the program 

Step1 

Step number of the first saved step 

Torque1 

Torque of the first saved step 

Angle1 

Angle of rotation of the step of the first saved step 

Step2 

Step number of the second saved step 

Torque2 

Torque of the second saved step 

Angle2 

Angle of rotation of the second saved step 

Step3 

Step number of the third saved step 

Torque3 

Torque of the step of the third saved step 

Angle3 

Angle of rotation of the step of the third saved step 

StepNOK 

Step number of the faulty step 

TorqueNOK 

Torque of the faulty step 

AngleNOK 

Angle of rotation of the faulty step 

-- reserved 
-- reserved 
Torque Unit 

Unit torque 

Angle Unit 

Angle of rotation unit 

Table 42: 

Structure of the data set in the files 1-7.csv and actual.csv 

 
 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды