manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 25

 

25 

7.6.1.3.2 Description of the data structure of the control signals (UDT21) 

Designation 

Data type  Description 

ReleaseStart BOOL 

Clearance to start for the  AST40 
This signal is currently not available yet! 

Start BOOL 

Clearance to start for the  AST40 

When the status of the start signal changes from "low" to 
"high", the pre-selected screwdriving program is started in 
the sequence controller ASTS40. The start signal must be 
present until the screwdriver operation has ended. 

ProgIn1 BOOL 

Input 1 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn2 BOOL 

Input 2 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn3 BOOL 

Input 3 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn4 BOOL 

Input 4 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn5 BOOL 

Input 5 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn6 BOOL 

Input 6 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn7 BOOL 

Input 7 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn8 BOOL 

Input 8 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn9 BOOL 

Input 9 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

ProgIn10 BOOL 

Input 10 for the screwdriver program 

This input can be scanned in the screwdriving program of 
the AST40 sequence control to stop or continue the 
screwdriving program. 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды