Deprag AST40-1 Скачать руководство пользователя страница 30

Страница: 30 / 153



An incorrect output module has been entered in the hardware configuration.

Output module 2 must be configured with "64 bytes out".



Incorrect start address of the output module 2 at the interface parameter

O_Addr2

FF13

Error while writing to the output module 3 (O_Addr3)

Possible causes:



An incorrect output module has been entered in the hardware configuration.

Output module 3 must be configured with "64 bytes out".



Incorrect start address of the output module 3 at the interface parameter

O_Addr3

FF14

Error while writing to the output module 4 (O_Addr4)

Possible causes:



An incorrect output module has been entered in the hardware configuration.

Output module 4 must be configured with "32 bytes out".



Incorrect start address of the output module 4 at the interface parameter

O_Addr4

F100

Timeout error in the fieldbus communication

Table 13:

Status Signal Error Codes

Содержание AST40-1


























































































































































Результаты поиска

Содержание AST40-1

Отзывы:

Бренды по названию

Популярные бренды

Deprag AST40-1, Руководство по эксплуатации

Результаты поиска

Содержание AST40-1

Отзывы:

Бренды по названию

Популярные бренды