Deprag AST40-1 Скачать руководство пользователя страница 110

Страница: 110 / 153

110

11.1.2 MINIMAT–EC-Servo Screwdriver

Parameters

Description

Offset gear

available

Indicates whether an adapter gear is available.

Gear ratio

Transmission ratio for the adapter gear

Efficiency

Effectiveness of the adapter gear

Direction change

Specifies whether the adapter gear causes change of
direction.

Table 35:

Adjustable Parameters MINIMAT–EC-Servo Screwdriver

11.2 Default values

11.2.1 Controller

The standard values for master control unit can be set in the web-based user interface in
the System menu area



System Settings. Open the "General" or "Fieldbus" sub-menu

and then click on the button "Default Values".
Alternately, you can set the standard values in the display within the System menu area



System Settings.

• Select "System Setup" to set the general parameters to standard values.
• Select "User Data" to delete the user data. Only the user "admin" remains with the

standard password 0000.

• Select "Fieldbus" to set the special parameters for the fieldbus to the standard

values.

Select “All” to set all parameters and user data to standard values.
Then touch

11.2.1.1 Standard values for system settings

Parameters

Value

Language English
Units of torque

Main direction of rotation

right

Rotation speed reduction

active

Beeper Never
Print string

@date_iso @time PG: @prog ST:
@step TQ: @torque AN: @angle
@errortext

Process display

Display for one measuring system

Fieldbus

available no

control by I/O interface

inactive

Table 36:

Default values

11.2.1.2 Standard values for user data

Parameters

Value

Users admin
Password (for Administrator)

0000

Table 37:

Standard values - User data

All the other user data were deleted.

Содержание AST40-1


























































































































































Результаты поиска

Содержание AST40-1

Отзывы:

Бренды по названию

Популярные бренды

Deprag AST40-1, Руководство по эксплуатации

Результаты поиска

Содержание AST40-1

Отзывы:

Бренды по названию

Популярные бренды