manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 31

 

31 

7.6.1.3.5 Description of the data structure of the screwdriving data (UDT23) 

Designation 

Data type  Description 

fd_Prog INT 

Program number 

The program number of the screwdriver program started 
previously is output here. 

fd_Status INT 

Screw status 

The screwdriver status is output here in detail. 
(for possible status values, see 

15.2 Error in the Screwdriving 

Sequence

) 

fd_Time REAL 

Screw fixing time 

The screw fixing time (in seconds) necessary of the program 
started previously is output here. 

fd_Step1 DINT 

Data backup

 step number

 

(1) 

The step number for the AST40 – program in which a data 
backup (1) occurred is output here 

fd_minTorque1 REAL 

Lower torque limit of 

Data backup

 (1) 

The set lower torque limit of the data backup (1) is output 
here. 

fd_tarTorque1 REAL 

Data backup

 torque setpoint 

(1)

 

The set lower torque setpoint of the data backup (1) is output 
here. 

fd_maxTorque1 REAL 

Data backup

 torque upper limit 

(1)

 

The set upper torque limit of the data backup (1) is output 
here. 

fd_Torque1 REAL 

Data backup

 torque setpoint 

(1)

 

The torque value of the data backup (1) is output here 

fd_minAngle1 DINT 

Lower angle of rotation limit of the 

Data backup

 (1) 

The set lower limit of the angle of rotation of the data backup 
(1) is output here. 

fd_tarAngle1 DINT 

Angle of rotation setpoint of the 

Data backup

 (1) 

The set angle of rotation setpoint of the data backup (1) is 
output here. 

fd_maxAngle1 DINT 

Upper limit of angle of rotation of the 

Data backup

 (1) 

The set upper limit of the angle of rotation of the data backup 
(1) is output here. 

fd_Angle1 DINT 

Angle of rotation value of the 

Data backup

 (1) 

The angle value of the data backup (1) is output here 

fd_Step2 DINT 

Data backup

 step number 

(2)

 

The step number for the AST40 – program in which a data 
backup (2) occurred is output here 

fd_minTorque2 REAL 

Lower torque limit of

 

Data backup

 (2) 

The set lower limit of the angle of rotation of the data backup 
(2) is output here. 

fd_tarTorque2 REAL 

Torque setpoint of the 

Data backup

 (2) 

The set lower torque setpoint of the data backup (2) is output 
here. 

fd_maxTorque2 REAL 

Upper torque limit of the 

Data backup

 (2) 

The set upper torque limit of the data backup (2) is output 
here 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды