Dell X1000 Series Скачать руководство пользователя страница 221

Страница: 221 / 416

Network Administration: Route Settings

221

FILE LOCATION: C:\Users\gina\Desktop\Checkout_new\Dell Astute\User

Guide\Dell_Astute_Network_Admin_RouteSettings.fm

D E L L CO N F I D E N T I A L – P R E L I M I N A RY 8 / 9 / 16 - F O R P RO O F O N L Y

–

Prefix Length

— The length of the IPv6 prefix. This field is applicable

only when the destination address is defined as a global IPv6 address.

–

Next Hop

— The type of address to which the packet is forwarded on

the route to the Destination address (typically the address of a

neighboring router). This can be either a

Link Local

Global

IPv6

address.

–

Interface

— The interface that is used to forward the packet. Interface

refers to any Port, LAG or VLAN.

–

Route

Type

— Specifies whether the destination is directly-attached

and the means by which the entry was learned. The possible options

are:
•

Local

— A directly-connected route entry.

•

Static

— Manually configured route, supported only for default

gateway, learned through the Neighbor Discover (ND) process.

•

ICMP

— The route was learned through ICMP Redirect

messages, sent by the router.

•

— Route was learned by the ND protocol from Router

Advertisement messages.

–

Metric

— The cost value used for comparing this route to other routes

with the same destination in the IPv6 route table.

–

Life-Time

— The timeout interval of the route if no activity takes

place. Infinite means the address is never deleted.

Click

Edit

Add

and enter the fields as described above for the new route.

NOTE:

A static route is displayed in the IPv6 Route table only if the IPv6 interface,

which is on the device, is connected to the Next Hop in the Up state.

ISATAP Tunnel

To deliver IPv6 addresses in an IPv4 network, a tunneling process must be

defined that encapsulates IPv6 packets in IPv4 packets.
The Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) is an IPv6

transition mechanism that is used to transmit IPv6 packets between

dual-stack nodes (nodes that can accept both IPv4 and IPv6 addresses) on top

of an IPv4 network.

Содержание X1000 Series

































































































































































































































































































































































































































Результаты поиска

Содержание X1000 Series

Отзывы:

Похожие инструкции для X1000 Series

Бренды по названию

Популярные бренды

Dell X1000 Series, Руководство пользователя

Результаты поиска

Содержание X1000 Series

Отзывы:

Похожие инструкции для X1000 Series

Бренды по названию

Популярные бренды