Dell Vostro 220 - Vostro 220 Slim Desktop Computer Скачать руководство пользователя страница 48

Страница: 48 / 138

Computer Cover

Release the computer cover by grasping the handle while sliding the cover
away from the front of the computer and lifting it up.

Replacing the Computer Cover

Ensure that all cables are connected and folded out of the way.

Ensure that no tools or extra parts are left inside the computer.

Ensure that the bezel is attached to the front of the computer (see
"Replacing the Bezel" on page 53).

NOTE:

The bezel must be installed before the cover is installed.

handle

computer cover

front of computer, bezel

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Руководство по обслуживанию

Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды