Dell Vostro 220 - Vostro 220 Slim Desktop Computer Скачать руководство пользователя страница 26

Страница: 26 / 138

Troubleshooting

• Verify that the mouse cable is connected as shown on the setup diagram for your

computer.

ESTART

THE

COMPUTER

—

Simultaneously press <Ctrl><Esc> to display the

Start

menu.

Press <

press the up- and down-arrow keys

to highlight

Shut down

Turn

Off

, and then press <Enter>.

After the computer turns off, reconnect the mouse cable as shown on the setup
diagram.

Turn on the computer.

EST

THE

MOUSE

—

Connect a properly working mouse to the computer, and then

try using the mouse.

HECK

THE

MOUSE

SETTINGS

—

Windows XP

Click

Start

→

Control Panel

→

Mouse

Adjust the settings as needed.

Windows Vista

Click

Start

→

Control Panel

→

Hardware and Sound

→

Mouse

Adjust the settings as needed.

EINSTALL

THE

MOUSE

DRIVER

THE

ARDWARE

ROUBLESHOOTER

—

See "Hardware Troubleshooter" on

page 12.

Network Problems

CAUTION:

Before you begin any of the procedures in this section, follow the

safety instructions that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at
www.dell.com/regulatory_compliance.

HECK

THE

NETWORK

CABLE

CONNECTOR

—

Ensure that the network cable is firmly

inserted into the network connector on the back of the computer and the network
jack.

HECK

THE

NETWORK

LIGHTS

THE

BACK

THE

COMPUTER

—

If the link

integrity light is off (see "About Your Computer" in the

Setup and Quick Reference

Guide

), no network communication is occurring. Replace the network cable.

ESTART

THE

COMPUTER

AND

LOG

THE

NETWORK

AGAIN

HECK

YOUR

NETWORK

SETTINGS

—

Contact your network administrator or the

person who set up your network to verify that your network settings are correct and

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Руководство по обслуживанию

Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды