Dell Vostro 220 - Vostro 220 Slim Desktop Computer Скачать руководство пользователя страница 103

Страница: 103 / 138

Memory Module(s)

103

Memory Module(s)

CAUTION:

Before working inside your computer, read the safety information that

shipped with your computer. For additional safety best practices information, see
the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

Removing Memory Modules

Follow the procedures in "Before Working on Your Computer" on page 35.

Remove the computer cover (see "Replacing the Computer Cover" on
page 48).

Locate the memory modules on the system board (see "System Board
Components" on page 40).

Press out the securing clip at each end of the memory module connector.

Grasp the module and pull it upwards.
If the module is difficult to remove, gently ease the module back and forth
to remove it from the connector.

securing clips (2)

memory module connector

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Руководство по обслуживанию

Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды