Dell Vostro 220 - Vostro 220 Slim Desktop Computer Скачать руководство пользователя страница 79

Страница: 79 / 138

Drives

For the Vostro 220s, push the release latch down to secure the optical drive
and the 3.5-inch device in their respective drive cages.

NOTE:

Install the media card reader into the drive bay before you connect the USB

interface cable to the back of the device.

Connect the USB interface cable to the back of the device.

NOTICE:

The connectors are "keyed" for correct insertion; that is, a notch or a

missing pin on one connector fits with a tab or a filled-in hole on the other
connector. Align the cable connectors correctly before inserting them to avoid
damage to the connectors.

Ensure that the other end of the USB interface cable is connected to a
USB connector on the system board (see "System Board Components" on
page 40).

Replace the bezel (see "Replacing the Bezel" on page 53).

screws (2)

screw holes (2)

media card reader

USB interface cable

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Руководство по обслуживанию

Результаты поиска

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer

Отзывы:

Похожие инструкции для Vostro 220 - Vostro 220 Slim Desktop Computer

Бренды по названию

Популярные бренды