Dell Vostro 220 - Vostro 220 Slim Desktop Computer Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 138

Dell Vostro 220 - Vostro 220 Slim Desktop Computer Скачать руководство пользователя страница 23

Troubleshooting

23

then try using the keyboard.

R

UN

THE

H

ARDWARE

T

ROUBLESHOOTER

—

See "Hardware Troubleshooter" on

page 12.

Lockups and Software Problems

CAUTION:

Before you begin any of the procedures in this section, follow the

safety instructions that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at
www.dell.com/regulatory_compliance.

The computer does not start up

C

HECK

THE

DIAGNOSTIC

LIGHTS

—

See "Power Lights" on page 9.

E

NSURE

THAT

THE

POWER

CABLE

IS

FIRMLY

CONNECTED

TO

THE

COMPUTER

AND

TO

THE

ELECTRICAL

OUTLET

The computer stops responding

NOTICE:

You may lose data if you are unable to perform an operating system

shutdown.

T

URN

THE

COMPUTER

OFF

—

If you are unable to get a response by pressing a key on

your keyboard or moving your mouse, press and hold the power button for at least 8 to
10 seconds (until the computer turns off), and then restart your computer.

A program stops responding

E

ND

THE

PROGRAM

—

1

Press <Ctrl><Shift><Esc> simultaneously to access the Task Manager.

2

Click the

Applications

tab.

3

Click to select the program that is no longer responding.

4

Click

End Task

.

A program crashes repeatedly

NOTE:

Most software includes installation instructions in its documentation or on a

CD or DVD.

C

HECK

THE

SOFTWARE

DOCUMENTATION

—

If necessary, uninstall and then reinstall

the program.

«
...
21
22
23
24
25
...
»

Содержание Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Отзывы:

Нет отзывов